Keep temperatures more constant when soldering lead with the Glastar Soldering Iron Control. Rated the most dependable and trouble-free on the market. Handling up to 1800 watts and equipped with a 3-prong grounded plug, it can regulate the temperature of any iron.

 SKU: 2175
Price: $44.25 (USD)

This soldering iron tip cleaner has a tray made of heat-resistant materials, skid resistant feet and a cellulose sponge that withstands heat. The most efficient way to clean off the residue that collects on a hot soldering iron. Frequent use of the Glastar Tip Cleaner not only extends the life of the tip but also improves its performance.

 SKU: 2183
Price: $6.65 (USD)

The Hakko Smoke Absorber pulls soldering fumes away from the iron safely, quickly and efficiently with a high performance, low noise fan. The filter is made of urethane foam with refined activated carbon which is of high absorbing quality. This device takes up minimal work-table space, and includes three filters. Replacement filters are also available. SPECIFICATIONS: Size: 8-3/4" x 10-5/8" x 6-5/8" (220 x 270 x 168mm) Weight: 3.31 lbs. (1500g) Power: 14 watts, 120 volts, 60 Hz AC Absorption capacity: 37.79 ft.3/min. (1.07m3/min.) Filter size: 5.1" x 5.1" x 0.4" (130 x 130 x 10mm)

 SKU: 2313
Price: $129.95 (USD)

Iron holder with 599B tip cleaner. Compatible with the Hakko Dash (N452, N452, N454) Mach (918, 920, 921, 922) and 455-456 irons and 808 desoldering gun.

 SKU: 23114
Price: $35.35 (USD)

Made of flux-dipped brass-wool. Requiring no water, it cleans the tip without temperature drop. Plunge the hot iron tip into the brass-wool to remove crust build-up. Brass case is 3" (76mm) in diameter. Non-skid buttons on the bottom.

 SKU: 2312
Price: $16.65 (USD)

The Inland FumeTrap provides a safer soldering environment by drawing fumes away from the person soldering and traps them in a disposable activated carbon filter. Key Features: A 110 CFM, axial type fan provides maximum fume intake up to 12-14" away. CFM is Cubic Feet Per Minute and measures the volume of air replaced each minute by the fan. The disposable activated carbon filter cartridge "snaps" into the rear of the housing and is easy to install or remove. Replacement filters are sold three to a pack. There is no time interval recommended for replacement of the filter since usage of the unit will vary. Indications that replacement is necessary is a visible blockage of the filter when holding the cartridge up to the light and it feels tacky or sticky to the touch. A top mounted handle and four non skid rubber feet make it very portable. The fixed front grill protects the user from the fan without restricting air flow. A 6 ft power cord provides plenty of reach. An in-line on/off switch makes it easy to operate. One Year Warranty. Product Uses: Anyone aware of the need for a safer environment when soldering is an excellent customer for a FumeTrap. All hobbyists that solder, glue, and paint should use a ventilation system that evacuates or collects and holds fumes, not re-circulating them as a simple blower fan would. The most effective system is one that filters and vents to the outside. (Before venting anything to the outside, check with your local government for emissions regulations.) Since most artists and hobbyists can't install such a system, the FumeTrap fills the need by removing and adsorbing the fumes and vapors created during these processes. Most fluxes generate organic and inorganic gases and vapors which we don't think about, but are also harmful with prolonged exposure. The FumeTrap provides an economic means of removing the fumes and vapors created when soldering stained glass. It's lightweight enough to place right on the project being soldered with soft rubber feet to protect the surface. Equipping classrooms with FumeTrap's is an effective way to demonstrate the product and improve safety awareness. Product Specs: Construction: Stamped steel housing. Color: Gray fleck body with plastic handle. Size: 5" wide x 5" high x 6" deep. Weight: 3 lb., 9 oz. 110 CFM (Cubic Feet / Minute of air moved) 115 VAC, 1 amp

 SKU: 21081
Price: $46.15 (USD)

The Inland MiniPhaser's solid state circuitry gives you solid temperature control all the time. Solder more effectively and efficiently with nearly any soldering iron.Key Features:- Solid state circuitry.- Better, more consistent temperature control.- Use with all Inland soldering irons and other non-tip controlled irons.- Three prong outlet for soldering iron won't pull out of base.- Easy read dial with on/off indicator.- Weighted base and non-skid feet.- Has a 6 foot heavy duty flexible power cord.- One year Warranty.Product Uses:- Maintain consistent soldering temperature for better control and less frustration.- Match soldering temperature to solder type for more effective soldering.- Match soldering temperature to the type of construction for more efficient soldering.- Solder at the speed that's most comfortable for you.- Manipulate solder for decorative and special effects.- Extend the reach of your iron when working on larger projects.- Expand and maximize the uses of your iron.Product Specs:Size: 3.75" wide x 4.5" deep x 2.0" high.Handles up to 600 Watts throughput.115V only.

 SKU: 2073
Price: $21.85 (USD)

Keeps your soldering iron handy and safe.Key Features:- Steel safety coil- Heavy metal base- Tip cleaning spongeProduct Uses:- Hold your iron safely, hot or cold.- Heavy base prevents stand from tipping over.- Handy tip cleaning sponge keeps tips free of debris for easier soldering.

 SKU: 2074
Price: $9.95 (USD)

The Inland SolderStation organizes the tools and supplies commonly used when soldering. Key Features: - A temperature control and outlet combination. The circuitry includes a grounded outlet, an LED on/off indicator and adjustable control dial. - A 6 foot grounded power cord is wired into the SolderStation, essentially extending the reach of the iron by 6 feet. This can be a huge benefit when working on a large flat project or a lampshade. - Cord router clips located along the left side of the plastic housing keep the iron cord away from the built-in iron stand. - A built-in coil-type iron holder with heat resistant collar fits most soldering irons. A metal drip plate is located below the iron holder with a well for a tip cleaning sponge. - A flux bottle well with a flux brush and a flux brush holder. The brush holder lets flux drip off the brush, back into the bottle, after the flux brush is used. - A solder spool post is sized to hold a full one pound roll of any solder. - A triangular flux sponge can be covered with liquid flux for easily fluxing foiled glass, rings or wire before tinning or soldering. - A catch all bin runs along the front for holding the flux bottle cap and provides a place to keep miscellaneous items such as rings, pins, or extra iron tips. - A pliers/tool well designed to hold mini-needle nose pliers which are a great aid for holding tiny rings or hinges while soldering. - One Year Warranty. Product Uses: - Anyone from beginner to skilled professional would appreciate the features and flexibility found in the SolderStation. - The built in temperature control extends the iron reach, and innovative features make the SolderStation a valuable soldering accessory. - Keeps all of your soldering tools and supplies handy and neat. Product Specs: Construction: Injection molded high impact plastic. Size: 9.5" wide x 6.0" deep x 1.5" high. Weight: 2.0 lb. 115 VAC.

 SKU: 21091
Price: $33.85 (USD)

Contemporary styling and a lighter-weight stand. Wide base stability and the double-barrel funnel design prevents burns, as the outer ring stays cool to the touch. Includes built-in tray and sponge.

 SKU: 2189
Price: $10.55 (USD)

This No-Spill Bottle Holder catches flux spills from careless hand movements or soldering iron cords. May also be used for bottles of patina or cutting oil.

 SKU: 2006
Price: $11.25 (USD)

This cast-iron base stand stays in place when soldering iron is removed & replaced. Accommodates irons with shafts up to 3/4" in diameter. Comes with sponge.

 SKU: 2188
Price: $10.65 (USD)

This "Pro" model soldering iron control features solid state circuitry. It's rated for 800 watts (8 amps at 110 volts AC).

 SKU: 2173
Price: $19.45 (USD)

1/2 lb. (227g) bar. Solid brick of Sal Ammoniac (Ammonium Chloride). Rub hot iron tip on brick to keep the tip bright and wet. Nonabrasive— will not damage tip.

 SKU: 5070
Price: $6.45 (USD)

A small application of Weller Anti-Bloc Paste (Anti-Seize Paste) keeps the socket end of soldering iron tips from freezing in place. 1/2 oz.

 SKU: 23196
Price: $8.65 (USD)

This larger sized soldering iron stand by Weller is made to hold the 100 watt Weller iron. Comes with sponge for tip cleaning.

 SKU: 23194
Price: $20.65 (USD)

Controlled soldering for the hobbyist or professional. Adjustable heat from 5 to 80 watts lets you control temperature as needed. Basic station includes 80-watt stained glass iron. Station is complete with temperature controller and holder. 120 volts, 60 Hz. Product Features: - On/off switch with "power-on" indicator light - Variable power control produces 5-80 watts - Quality lightweight stained glass iron - Cushioned foam grip with replaceable heating element - Ideal for the professional or hobbyist - Safety guard iron holder - Natural sponge tip cleaning pad - Includes MTG20 3/8" replaceable tip - UL listed

 SKU: 23074
Price: $63.55 (USD)